Arduino Project: Auto Water Level
Auto Water Level adalah projek yang memaparkan peratusan level air dan mengawal nya. Sekiranya level air telah 0%, relay akan dihidupkan bagi menghidupkan pam air dan memasukkan air semula. Sekiranya level air telah 100%, relay akan dimatikan bagi menghentikan pam air. Bagi versi PIC, boleh rujuk PIC Project: Auto Water Level.
Skematiknya adalah seperti berikut.
PCB komponen layout nya adalah seperti berikut.
| No | Component | Label | Unit |
|---|---|---|---|
| 1 | Capacitor Ceramic 0.1uF | C3-C4 | 2 |
| 2 | Capacitor Ceramic 22pF | C5-C6 | 2 |
| 3 | Capacitor Electrolytic 10uF | C1-C2 | 2 |
| 4 | Crystal 16MHz | XTAL | 1 |
| 5 | DC Jack Female | DC Jack Female | 1 |
| 6 | Diode 1N4001 | D1-D2 | 2 |
| 7 | IC ATMEGA328P DIP | ATMEGA328 | 1 |
| 8 | IC Socket 28pin | ATMEGA328 | 1 |
| 9 | LCD 16X2 | LCD | 1 |
| 10 | LED Red 5mm | LED1 | 1 |
| 11 | PCB 1 layer | PCB | 1 |
| 12 | PCB Connector Header (Right) 3 Ways | SEN1-SEN5 | 5 |
| 13 | PCB Connector Housing 3 Ways | SEN1-SEN5 | 5 |
| 14 | PCB Stand (screw nut) | PCB Stand | 6 |
| 15 | Relay 12V SPDT | RLY | 1 |
| 16 | Resistor 0.25W 10K | R1 | 1 |
| 17 | Resistor 0.25W 1K | R3-R8 | 6 |
| 18 | Resistor 0.25W 1K/4.7K | R2 | 1 |
| 19 | Resistor 0.25W 330 | R9 | 1 |
| 20 | Sensor Water Level Float Switch | SEN1-SEN5 | 5 |
| 21 | Slide Switch | S1 | 1 |
| 22 | Straight Pin Header (Male) | ICSP | 1 |
| 23 | Terminal Block 2 Way | DC | 1 |
| 24 | Terminal Block 3 Way | OUT | 1 |
| 25 | Terminal Pin | SEN1-SEN5 | 15 |
| 26 | Transistor 2N2222 | Q1 | 1 |
| 27 | Voltage Regulator 5V TO220 | 7805 | 1 |
Harga projek Arduino Auto Water Level adalah RM330 tidak termasuk bantuan teknikal. Di bawah adalah cara projek ini berfungsi.
I am from india required 1 board pls send price and other details
Complete project is MYR400 (USD102)
Hi..monitoring suhu via sms ada jl??
Monitoring suhu melalui sms sama seperti projek http://shahrulnizam.com/arduino-project-gsm-temperature
Coding di sertakan sekali ??
Jika beli projek, coding akan di berikan.
dear
sir i try to make Arduino Auto Water Level all follow your project but problem is my project did not show level of water only relay on and off doing. if all sensors close condition. can you help me?
I’m not doing free job, need to pay.
sir do you have the diagram of this projet?
I like this project
Aslmkm encik.. projek ini siap dgn pum skali ke?
w/salam, pump harga lain.